Introduction:
The Heckler & Koch MP5 is a 9mm submachine gun of German design, developed by a team of engineers from the German small arms manufacturer Heckler & Koch GmbH (H&K) of Oberndorf am Neckar in the 1960s.
Heckler & Koch, encouraged by the success of the G3 automatic rifle, developed a family of small arms consisting of four types of firearms (all based on a common G3 design layout and operating principle), where the first type was chambered in 7.62x51mm NATO, the second—using the 7.62x39mm M43 round, third—the intermediate 5.56x45mm NATO caliber and the fourth type—chambering the 9x19mm Parabellum pistol cartridge. The MP5 was created within the fourth group of firearms and was initially known as the HK54.
The MP5 is manufactured under license in several nations including Greece (formerly at EBO - Hellenic Arms Industry, currently at EAS - Hellenic Defense Systems), Iran (Defense Industries Organization), Mexico (SEDENA), Pakistan (Pakistan Ordnance Factories), Saudi Arabia, Sudan (Military Industry Corporation), Turkey (MKEK), and the United Kingdom (initially at Royal Ordnance, later diverted to Heckler & Koch Great Britain).
Design details:
The MP5A2, which is the primary version of the MP5 family, is a lightweight, air-cooled, selective fire delayed blowback operated 9x19mm Parabellum weapon with a roller-delayed bolt. It fires from a closed bolt (bolt forward) position.
The fixed, free floating, cold hammer-forged barrel has 6 right-hand grooves with a 1 in 250 mm (1:10 in) rifling twist rate and is pressed and pinned into the receiver.
Features:
The first MP5 models used a double-column straight box magazine, but since 1977, slightly curved, steel magazines are used with a 15-round capacity (weighing 0.12 kg) or a 30-round capacity (0.17 kg empty).The sighting arrangement on the MP5 takes advantage of the natural ability of the eye and brain to easily align concentric circles (circles all having a common center). The mechanically adjustable iron sights (closed type) consist of a rotating rear diopter drum and a front post installed in a hooded ring. The rear sight is adjustable for both windage and elevation with the use of a special tool; the drum provides four different apertures of varying width used for firing at 25, 50, 75 and 100 m. However, adjusting the rear drum does not change the elevation or bullet strike of the rounds since the MP5 uses pistol cartridges, which share a similar point of impact between 25 and 100 m when zeroed at 25 m.
The MP5 has a hammer firing mechanism. The trigger group is housed inside an interchangeable polymer trigger module (with an integrated pistol grip) and equipped with a 3-position fire mode selector that serves as the manual safety toggle. The “S” or Sicher position in white denotes weapon safe, “E” or Einzelfeuer in red represents single fire, and “F” or Feuerstoß (also marked in red) designates continuous fire. The SEF symbols appear on both sides of the plastic trigger group. The selector lever is actuated with the thumb of the shooting hand and is located only on the left side of the original SEF trigger group or on both sides of the ambidextrous trigger groups. The safety/selector is rotated into the various firing settings or safety position by depressing the tail end of the lever. Tactile clicks (stops) are present at each position to provide a positive stop and prevent inadvertent rotation. The "safe" setting disables the trigger by blocking the hammer release with a solid section of the safety axle located inside the trigger housing.
The non-reciprocating cocking handle is located above the handguard and protrudes from the cocking handle tube at approx. a 45° angle. This rigid control is attached to a tubular piece within the cocking lever housing called the cocking lever support, which in turn, makes contact with the forward extension of the bolt group. It is not however connected to the bolt carrier and therefore cannot be used as a forward assist to fully seat the bolt group. The cocking handle is held in a forward position by a spring detent located in the front end of the cocking lever support which engages in the cocking lever housing. The lever is locked back by pulling it fully to the rear and rotating it slightly clockwise where it can be hooked into an indent in the cocking lever tube.
Operating mechanism:
The bolt rigidly engages the barrel extension – a cylindrical component welded to the receiver that the barrel is pinned into. The delay mechanism is of the same design as that used in the G3 rifle. The two-part bolt consists of a bolt head with rollers and a bolt carrier. The heavier bolt carrier lies up against the bolt head when the weapon is ready to fire and inclined planes on the front locking piece lie between the rollers and force them out into recesses in the barrel extension.
The roller-delayed blowback mechanism originated from the aborted StG 45(M) assault rifle prototypes developed in Nazi Germany at the end of World War II.
When fired, expanding propellant gases produced from the burning powder in the cartridge exert rearward pressure on the bolt head transferred through the base of the cartridge case as it is propelled out of the chamber. A portion of these forces is transmitted through the rollers projecting from the bolt head, which are cammed inward against the inclined flanks of the locking recesses in the barrel extension and to the angled shoulders of the locking piece. The selected angles of the recesses and the incline on the locking piece produce a velocity ratio of about 4:1 between the bolt carrier and the bolt head. This results in a calculated delay, allowing the projectile to exit the barrel and gas pressure to drop to a safe level before the case is extracted from the chamber.
The delay results from the amount of time it takes for enough recoil energy to be transferred through to the bolt carrier in a sufficient quantity for it to be driven to the rear against the force of inertia of the bolt carrier and the forward pressure exerted against the bolt by the recoil spring. As the rollers are forced inward they displace the locking piece and propel the bolt carrier to the rear. The bolt carrier's rearward velocity is four times that of the bolt head since the cartridge remains in the chamber for a short period of time during the initial recoil impulse. After the bolt carrier has traveled rearward 4 mm, the locking piece is withdrawn fully from the bolt head and the rollers are compressed into the bolt head. Only once the locking rollers are fully cammed into the bolt head can the entire bolt group continue its rearward movement in the receiver, breaking the seal in the chamber and continuing the feeding cycle.
Since the 9x19mm Parabellum cartridge is relatively low powered, the bolt does not have an anti-bounce device like the G3, but instead the bolt carrier contains tungsten granules that prevent the bolt group from bouncing back after impacting the barrel extension. The weapon has a fluted chamber that enhances extraction reliability by bleeding gases backwards into the shallow flutes running along the length of the chamber to prevent the cartridge case from expanding and sticking to the chamber walls (since the bolt is opened under relatively high barrel pressure). A spring extractor is installed inside the bolt head and holds the case securely until it strikes the ejector arm and is thrown out of the ejection port to the right of the receiver. The lever-type ejector is located inside the trigger housing (activated by the movement of the recoiling bolt).
Accessories:
Three lugs are provided at the muzzle that are used to work with certain muzzle devices made by Heckler & Koch, including: a slotted flash suppressor, blank firing attachment (marked with a red painted band denoting use with blank ammunition only), an adaptor for launching rifle grenades (for use with rifle-style grenades with an inside diameter of 22 mm using a special grenade launching cartridge) and a cup-type attachment used to launch tear gas grenades.
The receiver housing has notches that permit the attachment of a standard Heckler & Koch quick-detachable scope mount (also used with the G3, HK33 and G3SG/1) that can be used to mount daytime optical sights (telescopic 4x24), night sights or a halogen flashlight. It can be used with reflex sights and laser pointers. The mount features two spring-actuated bolts, positioned along the base of the mount, which exert pressure on the receiver to hold the mount in the same position at all times assuring zero retention. All versions of the quick-detachable scope mount provide a sighting tunnel through the mount so that the shooter can continue to use the fixed iron sights with the scope mount attached to the top of the receiver.
Specifications:
Weight: 2.54 kg (5.6 lb) (MP5A2, MP5A4)
3.08 kg (6.8 lb) (MP5A3, MP5A5)
2 kg (4.4 lb) (MP5K, MP5KA1, MP5KA4, MP5KA5)
2.78 kg (6.1 lb) (MP5K-PDW)
2.80 kg (6.2 lb) (MP5SD1, MP5SD4)
3.10 kg (6.8 lb) (MP5SD2, MP5SD5)
3.60 kg (7.9 lb) (MP5SD3, MP5SD6)
2.67 kg (5.9 lb) fixed stock / 2.85 kg (6.3 lb) retractable stock (MP5/10)
2.67 kg (5.9 lb) fixed stock / 2.85 kg (6.3 lb) retractable stock (MP5/40)
Length Fixed: stock: 680 mm (26.8 in) (MP5A2, MP5A4, MP5/10, MP5/40)
790 mm (31.1 in) (MP5SD2, MP5SD5)
Telescoping stock: 700 mm (27.6 in) stock extended / 550 mm (21.7 in)
stock collapsed (MP5A3, MP5A5)
603 mm (23.7 in) stock extended / 368 mm (14.5 in)
stock folded (MP5K-PDW)
805 mm (31.7 in) stock extended / 670 mm (26.4 in)
stock collapsed (MP5SD3, MP5SD6)
660 mm (26.0 in) stock extended / 490 mm (19.3 in)
stock collapsed (MP5/10, MP5/40)
Receiver end cap: 325 mm (12.8 in) (MP5K, MP5KA1, MP5KA4, MP5KA5)
349 mm (13.7 in) (MP5K-PDW)
550 mm (21.7 in) (MP5SD1, MP5SD4)
Barrel length: 225 mm (8.9 in) (MP5A2, MP5A3, MP5A4, MP5A5, MP5/10, MP5/40)
115 mm (4.5 in) (MP5K, MP5KA1, MP5KA4, MP5KA5)
140 mm (5.5 in) (MP5K-PDW)
146 mm (5.7 in) (MP5SD1, MP5SD2, MP5SD3, MP5SD4, MP5SD5, MP5SD6)
Width: 50 mm (2.0 in) (MP5A2, MP5A3, MP5A4, MP5A5, MP5K, MP5KA1,
MP5KA4, MP5KA5, MP5K-PDW, MP5/10, MP5/40)
60 mm (2.4 in) (MP5SD1, MP5SD2, MP5SD3, MP5SD4, MP5SD5, MP5SD6)
Height: 260 mm (10.2 in) (MP5A2, MP5A3, MP5A4, MP5A5, MP5SD1, MP5SD2,
MP5SD3, MP5SD4, MP5SD5, MP5SD6, MP5/10, MP5/40)
210 mm (8.3 in) (MP5K, MP5KA1, MP5KA4, MP5KA5, MP5K-PDW)
Cartridge: 9x19mm Parabellum
10mm Auto (MP5/10)
.40 S&W (MP5/40)
Action: Roller-delayed blowback, closed bolt
Rate of fire: 700 rounds/min (MP5SD series),
800 rounds/min (MP5A series, MP5/10 and MP5/40),
900 rounds/min (MP5K series)
Muzzle velocity: 400 m/s (1,312 ft/s) (MP5A2, MP5A3, MP5A4, MP5A5)
375 m/s (1,230.3 ft/s) (MP5K, MP5KA1, MP5KA4, MP5KA5, MP5K-PDW)
285 m/s (935.0 ft/s) (MP5SD1, MP5SD2, MP5SD3, MP5SD4, MP5SD5,
MP5SD6)
425 m/s (1,394.4 ft/s) (MP5/10)
315 m/s (1,033.5 ft/s) (MP5/40)
Effective range: 25 to 100 m sight adjustments
Maximum range: 150 m
Feed system: 15 or 30-round detachable box magazine,
100-round Beta C-Mag drum magazine
Sights: Rear: rotary drum
front: hooded post
No comments:
Post a Comment